-->
Our Process Gallery Why Choose Us

●

Now Booking Michigan Fence Builds & Gate Installations • Free On-Site Estimates

Metro Detroit & Ann Arbor

FENCE CARE GUIDE

|

Cleaning Bare Wood

Can You Use Dawn on an Untreated Wood Fence?

Yes. A mild Dawn and warm-water mix is safe on bare cedar and pine and lifts dirt, pollen and grease. It will not kill mildew or bring back gray wood, so here is when to use it, what to use instead, and how to rinse so your stain still soaks in.

Safe Mix Ratio Inside

Low Pressure, Soft Brush

Rinse Before Staining

Cedar & Pine Specific

DIRECT DISPATCH PHONE

Get Your Free Estimate

Quick response guaranteed within 24 hours

Online Booking Open

🔒 Your contact info is strictly confidential. We never sell your data or spam you.

KEY TAKEAWAYS

What Dish Soap Does, and Does Not Do, to Bare Wood

Dawn is a degreaser, not a wood cleaner. That makes it useful for some jobs on an unfinished fence and the wrong tool for others.

Safe at the Right Strength

About 2 tablespoons of Dawn per gallon of warm water cleans without leaving a heavy film. More soap is not more clean; it is more rinsing.

2 Tbsp per gallon

Removes Dirt, Not Mildew

Soap lifts grime, sap, grill smoke and pollen. Black mildew spots and green algae come back within weeks unless an oxygen bleach wash kills them.

Use oxygen bleach for mold

Will Not Fix Gray Wood

Silver-gray cedar is UV-damaged surface fiber. Only a light sanding or an oxalic acid brightener after cleaning restores the color.

Brightener restores tone

Rinse It All Off

Soap residue left in the grain can keep a penetrating stain from soaking in and cause blotchy color. Rinse until there are no suds.

Dry 48 hours before stain

CHOOSING A CLEANER

Dawn vs. Oxygen Bleach vs. Chlorine Bleach on Untreated Wood

Untreated means no stain or sealer: new cedar, weathered cedar, or pressure-treated pine that was never finished. Bare wood soaks up whatever you put on it, so the cleaner matters more than on a sealed fence. Dawn and water is the gentlest option and fine for routine cleaning. Oxygen bleach (sodium percarbonate, sold as powdered deck and fence wash) is the right choice for mildew because it kills spores without bleaching the fibers.

Chlorine bleach is the one to skip on cedar. It whitens the surface unevenly, breaks down lignin so the wood fuzzes, and burns lawns and shrubs along the fence line. If the fence will be stained, finish with an oxalic acid brightener, let it dry two days, and follow our how to stain a fence steps or have our staining and sealing crew do it.

CLEANERS ON BARE WOOD

Removes

Use On Cedar?

Dawn + Warm Water

2 Tbsp per gallon

Dirt, sap, grease

Yes, routine

Oxygen Bleach Wash

Sodium percarbonate

Mildew, algae, gray

Yes, best choice

Oxalic Acid Brightener

After cleaning

Tannin, rust stains

Yes, before stain

Chlorine Bleach

Household bleach

Mildew stains

Avoid

Pressure Washer Only

Over 1,500 psi

Everything, fibers too

Avoid

STEP BY STEP

How to Clean an Untreated Wood Fence With Dawn

Plan on about an hour per 50 feet of 6-foot fence, one side, on a cloudy day so the solution does not dry on the boards.

01

Step 1

Prep the Fence and Plants

Wet the grass and shrubs along the fence line, then wet the boards. Mix 2 tablespoons of Dawn into a gallon of warm water in a pump sprayer or bucket.

Soak plants with plain water first

Pre-wet boards top to bottom

Test on one hidden board

LOW PRESSURE

02

Step 2

Scrub With the Grain

Apply from the bottom up so there are no streaks, let it sit 5 to 10 minutes without drying, and scrub with a soft nylon brush along the grain.

Work 6 to 8 feet at a time

Soft brush, never wire

Spot-treat mildew with oxygen bleach

03

Step 3

Rinse, Brighten, Dry

Rinse top down with a garden hose or a pressure washer on a 40-degree tip held 12 inches away. Brighten if staining, then let the wood dry at least 48 hours.

Rinse until no suds remain

Under 800 psi on cedar

Stain only once boards are dry

Fuzzy Boards After Washing?

That is raised grain from too much pressure. Let it dry and sand lightly with 80-grit before staining, or the fuzz will soak up stain unevenly.

BARE WOOD TIPS

Keeping an Untreated Fence Looking Good

Cleaning is half the job. These habits decide whether bare wood lasts 10 years or 25.

Seal Within the First Year

New pressure-treated pine needs a few months to dry; cedar can be sealed within weeks. A penetrating oil-based sealer slows graying and checking. See our fence sealant guide.

Clean Every Spring

A once-a-year Dawn wash removes pollen and the grime mildew feeds on. Oxygen bleach every second or third year handles the rest.

Keep Soil and Mulch Off Boards

Wood touching wet soil rots first. Keep a 2-inch gap under pickets and pull mulch back from the bottom rail.

Trim Shrubs Back 12 Inches

Plants against the fence hold moisture against the boards and block the sun that dries them. Shaded north faces mildew fastest.

Gray Is Not Rot

Silver cedar is still sound. Push a screwdriver into the bottom of a post or rail: if it sinks in, that is rot and the board needs replacing, not washing.

Know When to Rebuild

If posts lean or more than a quarter of the boards are cracked, cleaning is wasted effort. Our wood fence installation team can quote a replacement.

FREQUENTLY ASKED QUESTIONS

Dawn and Untreated Wood Fence Questions

Quick answers on soap, bleach and staining.

Is Dawn dish soap safe for an untreated cedar fence?

Yes, diluted to about 2 tablespoons per gallon of warm water and rinsed off thoroughly. It does not damage cedar fibers. Heavy concentrations leave residue that can interfere with stain.

Does Dawn kill mold and mildew on a wood fence?

Not reliably. Soap removes the surface stain but leaves live spores in the grain. Use an oxygen bleach wash, about one cup of sodium percarbonate per gallon of warm water, and let it sit 10 to 15 minutes before scrubbing.

Can I mix Dawn and bleach to clean a fence?

Dawn with a small amount of household bleach is a common mix and is not dangerous the way bleach and ammonia are, but we do not recommend chlorine bleach on bare cedar. It whitens the wood unevenly and damages plants. Oxygen bleach with a little Dawn as a wetting agent works better.

Will Dawn hurt my grass or plants?

Diluted Dawn is fairly mild, but it can still spot leaves. Wet plants before you start and rinse them afterward. Never let runoff pool around shrub roots.

How long after washing can I stain an untreated fence?

At least 48 hours of dry weather, longer for pressure-treated pine. Splash a little water on a board: if it beads, wait; if it soaks in within a minute, the wood is ready for a penetrating stain.

Should I use a pressure washer on untreated wood?

Only on low pressure, under about 800 psi on cedar, with a wide 40-degree tip held 12 inches off the surface. High pressure tears soft cedar fibers and leaves a fuzzy surface. A garden hose rinse is usually enough after a soap scrub.

WOOD FENCE CARE

Want the Fence Cleaned and Sealed for You?

We wash, brighten and seal cedar and pressure-treated fences across Metro Detroit, and replace boards and posts that are past saving.

PREFER TO CALL DIRECTLY?

Speak directly with our estimating desk for quick questions or emergency repairs.

Oxygen-bleach wash that is safe for cedar

Penetrating stain applied once wood is dry

Rotted boards and leaning posts repaired

Get Your Free Estimate

Quick response guaranteed within 24 hours

Online Booking Open

🔒 Your contact info is strictly confidential. We never sell your data or spam you.