-->
Our Process Gallery Why Choose Us

●

Now Booking Michigan Fence Builds & Gate Installations • Free On-Site Estimates

Metro Detroit & Ann Arbor

FENCE GUIDE

|

Step-by-Step

How to Apply Stain to a Wood Fence

A fence stain lasts as long as the prep under it. Clean, dry wood, the right weather window and a penetrating stain worked into the grain will get three to five Michigan winters out of one coat. Here is the full process, the coverage math, and what it costs if you would rather hand it off.

Moisture Test Before Staining

50–90 Degree Weather Window

Back-Brush Every Sprayed Board

Recoat Every 2–5 Years

DIRECT DISPATCH PHONE

Get Your Free Estimate

Quick response guaranteed within 24 hours

Online Booking Open

🔒 Your contact info is strictly confidential. We never sell your data or spam you.

THE SHORT ANSWER

Four Things That Decide Whether a Stain Job Lasts

Most peeling, blotchy or short-lived fence stain traces back to one of these four mistakes, not to the brand of stain.

Dry Wood First

Sprinkle water on a board. If it beads, the wood is still too wet or still has mill glaze. If it soaks in within a few minutes, it is ready.

Pressure-treated: often 1–3 months

Clean, Then Wait

Wash off mildew, gray fibers and dirt, then let the fence dry at least 48 hours. Stain over damp or dirty wood fails first.

Low-pressure wash, 500–1,200 PSI

Penetrate, Do Not Coat

Semi-transparent oil or hybrid stains soak in and wear away evenly. Thick solid stains and paint film over and peel on fences.

One saturating coat, no puddles

Watch the Forecast

Stain between roughly 50 and 90 degrees, out of direct midday sun, with no rain expected for 24 to 48 hours.

Late May to September in Michigan

CHOOSING A STAIN

Which Fence Stain to Use and How Much to Buy

For most cedar and pressure-treated pine fences, a semi-transparent penetrating stain is the right balance: enough pigment to block UV graying, thin enough to soak in and fade gracefully instead of peeling. Transparent toners look great on new cedar but need recoating every one to two years. Solid stains hide mismatched boards but behave like paint and eventually flake, which turns the next job into scraping. If you are unsure what is on the fence now, see our notes on fence sealants.

Rough-sawn fence boards are thirsty. Plan on roughly 150 to 250 square feet per gallon per coat, not the 300-plus printed for smooth decking. Measure length times height for each side you are staining. A 150-foot run of 6-foot privacy fence is 900 square feet per side, so budget 4 to 6 gallons for one side and 8 to 12 for both, plus posts, rails and a little spare for touch-ups.

STAIN TYPES AT A GLANCE

Typical Life

Recoat Effort

Clear Sealer

Water repellent only

1 year

Easy, no stripping

Transparent Toner

Light pigment, shows grain

1–2 years

Easy, wash and recoat

Semi-Transparent

Best for most fences

2–4 years

Easy, wash and recoat

Solid Color Stain

Hides grain like paint

4–6 years

Scraping when it peels

Coverage Rate

Rough-sawn boards

150–250 sq ft/gal

Per coat

HOW TO STAIN A FENCE

Prep, Apply and Protect in Three Stages

A single person with a pump sprayer and a brush can do about 100 to 150 linear feet of one side per day once prep is done. Prep usually takes as long as staining.

01

Step 1

Repair, Clean & Dry

Fix the fence before you finish it. Reset loose boards, replace split pickets, then wash with a wood cleaner or oxygen bleach and a low-pressure rinse. Let it dry for two days.

Drive popped nails, replace rot

Brighten gray wood with cleaner

Dry 48 hours before staining

DO NOT SKIP

02

Step 2

Mask & Test

Cover plants, siding, concrete and hardware with drop cloths and painter's tape. Stir the stain fully and test a hidden board to confirm color and absorption.

Tape hinges, latches and caps

Mix all cans together for color

Test-board color after it dries

03

Step 3

Apply & Back-Brush

Spray or roll two or three boards at a time, top to bottom, then immediately work the stain into the grain with a 3- to 4-inch brush. Keep a wet edge and wipe drips before they dry.

Work with the grain, top down

Coat board edges and rail tops

Wipe excess within 15 minutes

Brand-New Fence?

Cedar can usually be stained within a few weeks. Kiln-dried or air-dried pressure-treated pine often needs one to three months before it passes the water test. Ask us when your new fence will be ready.

PRO TIPS

Details That Separate a Clean Job From a Blotchy One

These are the habits our crews use on every fence staining and sealing job.

Stain in the Shade

Follow the shade around the yard. Direct sun flashes the solvent off before the stain soaks in and leaves lap marks.

Never Let It Puddle

Excess stain that sits on the surface turns sticky and glossy, then peels. Back-brush until the board looks evenly wet, not shiny.

Do the End Grain

Post tops, picket tops and board ends soak up water fastest. Give them an extra pass; a post cap helps even more.

Keep It Off the Ground

Trim grass and pull mulch back from the bottom of the boards first so the lowest inches get coated and stay dry.

Box the Cans

Pour all the gallons into one bucket and mix. Small batch-to-batch color differences show up as stripes on a long fence.

Dispose of Rags Safely

Oil-stain rags can self-heat and ignite. Lay them flat outdoors to dry or keep them in a sealed can of water.

Pick the Right Cleaner

Oxygen bleach or a wood cleaner is safer for boards than chlorine bleach. Our fence wash guide compares options.

Know When to Wash Only

If water still beads on last year's stain, wait. Recoat when water soaks in and the color looks thin on the sunny side.

FREQUENTLY ASKED QUESTIONS

Fence Staining Questions

Straight answers on timing, tools and cost.

Is it better to spray, roll or brush stain on a fence?

Spray or roll for speed, then back-brush. A sprayer alone leaves stain sitting on the surface; brushing it in gives better penetration and a more even color. Brushing only is fine for short runs.

How long after installing a new fence should I stain it?

When it passes the water test. Cedar is often ready in two to four weeks, while pressure-treated pine commonly needs one to three months to dry. Staining too soon traps moisture and the stain will not absorb.

Do I need two coats of fence stain?

Usually not with semi-transparent stain on rough wood. One saturating coat, back-brushed, is standard. Some products allow a second coat wet-on-wet within an hour or two; follow the label, because a second coat applied after the first dries often just sits on top.

How much does it cost to have a fence stained?

Most professional staining on a 6-foot privacy fence lands between about $4 and $12 per linear foot, depending on one side or both, how much washing and repair is needed, and the stain chosen. Prep-heavy older fences sit at the top of that range.

How often should a fence be restained in Michigan?

Plan on every two to four years for semi-transparent stain, sooner on south- and west-facing sides. Freeze-thaw cycles and summer UV wear the sunny side about twice as fast as the shaded side.

Can I stain a fence in the fall?

Yes, if daytime temperatures stay above about 50 degrees and nights do not drop near freezing before the stain cures. In Metro Detroit that window usually closes by early October.

FREE STAINING QUOTE

Rather Have Your Fence Stained for You?

We wash, repair and stain wood fences across Wayne, Oakland and Macomb counties. Learn more about our fence staining and sealing service or request a free measurement.

PREFER TO CALL DIRECTLY?

Speak directly with our estimating desk for quick questions or emergency repairs.

Board repairs done before any stain goes on

Penetrating stain back-brushed into the grain

Plants, siding and hardware protected

Get Your Free Estimate

Quick response guaranteed within 24 hours

Online Booking Open

🔒 Your contact info is strictly confidential. We never sell your data or spam you.