-->
Our Process Gallery Why Choose Us

●

Now Booking Michigan Fence Builds & Gate Installations • Free On-Site Estimates

Metro Detroit & Ann Arbor

CHAIN LINK GUIDE

|

Posts & Hardware

Chain Link Fence Terminal Posts Explained

Terminal posts are the end, corner and gate posts that the whole chain link fence is stretched between. They are larger than line posts, set deeper, and carry all the fabric tension. Here are the sizes, depths and hardware to get right.

Sizes by Fence Height

42″ Michigan Setting Depth

Hardware Checklist

Repair vs. Replace Costs

DIRECT DISPATCH PHONE

Get Your Free Estimate

Quick response guaranteed within 24 hours

Online Booking Open

🔒 Your contact info is strictly confidential. We never sell your data or spam you.

KEY TAKEAWAYS

What a Terminal Post Does

Line posts only hold the fabric up. Terminal posts hold it tight. That difference drives every spec below.

Three Kinds of Terminal

End posts finish a run, corner posts turn it, and gate posts hang gates. All three anchor the fabric with a tension bar.

End, corner, gate

Bigger Than Line Posts

A residential fence pairs 1-5/8-inch line posts with 2-3/8-inch terminals. Commercial work steps up to 2-7/8 inches or more.

One size up, minimum

Set Below Frost

In Michigan, frost reaches about 42 inches. A shallow terminal heaves, leans inward and lets the fabric sag along the whole run.

42″ in concrete

Corners at Every Turn

Any change in direction of more than about 10 degrees needs a corner terminal, not a line post with the fabric wrapped around it.

No wrapped corners

SIZING & DEPTH

Terminal Post Sizes, Lengths and Setting Depth

Chain link pipe is sized by outside diameter (OD). For residential fences 4 to 6 feet tall, 2-3/8-inch OD terminals are standard. Gate posts for walk gates use the same size; drive gates over 12 feet and commercial fences need 2-7/8-inch, 4-inch or larger, depending on gate width and weight. Our structural gate posts page covers the heavier end. Wall thickness matters too: thin-wall big-box posts bend where heavier schedule 40 pipe will not.

Length is fence height plus about 2 inches above the fabric, plus setting depth. On our builds that depth is 42 inches in a 10- to 12-inch concrete footing with a crowned top that sheds water, so a 4-foot fence takes a terminal about 8 feet long. Many installs use 24 to 30 inches, which is why so many older terminals in Metro Detroit lean. See chain link fencing for our full build spec.

RESIDENTIAL TERMINAL SPEC

4 ft Fence

6 ft Fence

Terminal OD

End and corner

2-3/8″

2-3/8″–2-7/8″

Post Length

At 42″ depth

About 8 ft

About 10 ft

Footing

Concrete diameter

10″

10″–12″

Tension Bands

Per terminal

3

5

Brace Rail

Mid-height

Optional

Recommended

INSTALLING A TERMINAL

How to Set a Chain Link Terminal Post

Terminals go in first and must cure before the fabric is stretched. Rushing that is the most common DIY mistake.

01

Step 1

Locate and Dig

Mark ends, corners and gates, call Miss Dig 811, and dig each hole about three times the post diameter wide and 42 inches deep, slightly bell-shaped at the bottom.

Miss Dig ticket before digging

10–12″ wide, 42″ deep

Wider at bottom to resist heave

LET IT CURE

02

Step 2

Set, Plumb and Cure

Set the post at the right height, plumb it on two faces, pour concrete and crown the top. Let it cure several days before applying fabric tension.

Height = fabric plus 2″

Plumb checked on two sides

Cure before stretching

03

Step 3

Hang the Hardware

Slide on tension bands and brace band, add the rail end cup and dome cap, then weave the tension bar through the fabric and bolt it to the bands.

Bands evenly spaced

Carriage bolts facing out

Dome cap keeps water out

Gate Posts Are Different

Hinge posts carry a twisting load every time the gate swings. Set them deepest, use the heaviest pipe on the job, and never hang a gate on a line post.

HARDWARE CHECKLIST

Fittings Every Terminal Post Needs

Missing one of these is why a fence looks fine on day one and sags by spring.

Tension Bands

Flat bands that clamp the tension bar to the post. The usual rule is one fewer than the fence height in feet: 3 on a 4-foot fence, 5 on a 6-foot.

Tension Bar

A flat steel bar woven through the last row of diamonds. It spreads the pull of the fabric along the full height of the post.

Brace Band and Rail End

A heavier band with a rail end cup that receives the top rail. It ties the rail to the terminal so the post cannot pull inward.

Dome Cap

Terminal posts take a dome cap; line posts take a loop cap the rail passes through. Caps keep water and ice out of the pipe.

Brace Rail and Truss Rod

On 6-foot and taller fences, a horizontal brace to the first line post and a diagonal truss rod stop the terminal from bowing.

Gate Hinges and Latch

Post hinges, a fork latch or drop rod, and a gate stop. See commercial chain link gates for heavier hardware.

RELATED SERVICES

Chain Link Builds and Repairs

Whether a single terminal is leaning or the whole run needs replacing, start here.

New Fence

Chain Link Fencing

Residential & Commercial

Galvanized and vinyl-coated chain link with properly sized terminals set below frost.

Terminals:

2-3/8″ and up

Depth:

42″ in concrete

Heights:

4 to 10 ft

Best For:

Yards, pets, lots

Built to spec, itemized

Repair

Leaning Post Replacement

Terminals and Line Posts

Heaved or bent posts are dug out with their footings, replaced with the right size pipe and reset below frost.

Footing:

Old concrete removed

Post:

Correct OD and wall

Fabric:

Re-stretched

Best For:

Leaning corners, ends

Fix it once

Heavy Duty

Structural Gate Posts

For Wide and Heavy Gates

Oversized gate posts and footings for drive gates, so hinges stay aligned and latches keep catching.

Sizes:

2-7/8″ to 6″

Footing:

Oversized, 42″+

Gates:

Swing and slide

Best For:

Drive and commercial gates

No more sagging gates

FREQUENTLY ASKED QUESTIONS

Chain Link Terminal Post Questions

Sizing, depth and repair.

What size terminal post do I need for a chain link fence?

For residential fences 4 to 6 feet tall, 2-3/8-inch OD is standard, paired with 1-5/8-inch line posts. Use 2-7/8-inch or larger for commercial fences, tall fences and drive gates over about 12 feet.

How deep should chain link terminal posts be set?

In Metro Detroit we set them 42 inches deep in concrete, below the frost line. Shallower terminals, 24 to 30 inches, tend to heave and lean within a few winters.

What is the difference between a terminal post and a line post?

Terminal posts sit at ends, corners and gates and anchor the stretched fabric with a tension bar. Line posts sit between them every 8 to 10 feet and just support the fabric and top rail. Terminals are larger and set in bigger footings.

How much does it cost to replace a chain link terminal post?

Most single terminal post replacements land between $200 and $450 installed, including breaking out the old footing, a new post and concrete, and re-stretching the fabric. Gate posts and posts near patios or driveways cost more.

Why is my chain link corner post leaning?

Usually a shallow footing that frost has lifted, a missing brace rail, or fabric over-stretched against a thin-wall post. Straightening it rarely lasts; resetting it below frost does. See leaning post replacement.

How far apart should chain link line posts be between terminals?

No more than 10 feet apart, and 8 feet on taller fences or where slats or screen will be added. Long straight runs also get an intermediate pull post so the fabric can be stretched in sections.

CHAIN LINK REPAIR & INSTALL

Get Your Chain Link Fence Fixed or Built Right

Leaning terminals, sagging fabric or a new run: we measure, explain the fix and give you a written price.

PREFER TO CALL DIRECTLY?

Speak directly with our estimating desk for quick questions or emergency repairs.

Terminals reset 42 inches in concrete

Fabric re-stretched and re-tied

Heavier gate posts where needed

Get Your Free Estimate

Quick response guaranteed within 24 hours

Online Booking Open

🔒 Your contact info is strictly confidential. We never sell your data or spam you.